New H480 Loader

Material Handling
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Superior strength and visibility
  • For heavy-duty chores
  • Parking stands are integrated on the loader

More Info

Features

False rod bucket cylinders improve productivity
False rod cylinderFalse rod cylinder
#

Fast bucket cycle times are important to dump the load from the bucket as quickly as possible, (quite often) in order to be as productive as possible, while completing loading operations. The bucket cylinder design can have a major impact on this cycle time, especially for the mechanical self-leveling loaders.

 

Therefore, all MSL H-Series Loaders utilize false rod bucket cylinders. A false rod cylinder has a smaller displacement of oil requirement on the head end of the cylinder, which allows this cylinder to dump much faster than a normal cylinder.

Boom lockout for easy service
Hydraulic shut-off valve (open position)Hydraulic shut-off valve (open position)
Hydraulic shut-off valve (closed position)Hydraulic shut-off valve (closed position)

A hydraulic shut-off valve is included with the H-Series Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.

Loader removal (parking) made easy
Parking standsParking stands
#

John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.

 

In order to remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, install the parking stands and place the mast pins in the open position.

 

To watch a video of parking and attaching an H-Series loader click here.

Removing or parking the loader
Bucket slightly dumped and down pressureBucket slightly dumped and down pressure
#
Parking stand in stored positionParking stand in stored position
Removing parking standRemoving parking stand
Bucket slightly dumped - Parking stands installedBucket slightly dumped - Parking stands installed
Mast pin in the closed positionMast pin in the closed position
Mast pin in the open positionMast pin in the open position

Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, rollback the bucket until the mast is removed from the pocket and will clear the tires.

Masts rotated forward, then bucket rolled backMasts rotated forward, then bucket rolled back
#

With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor. Relieve pressure on the single-point hydraulic connection, then disconnect or open the single-point hydraulic connector.

Parked loaderParked loader
Relieving the hydraulic pressureRelieving the hydraulic pressure
Disconnect/open single point hydraulic connectionDisconnect/open single point hydraulic connection

Store the loader half of the single-point connector. The tractor is now ready to back away from the loader.

Storing the hydraulic hosesStoring the hydraulic hoses
#
Tractor ready to be backed away from loaderTractor ready to be backed away from loader
Backing away from loaderBacking away from loader
Concealed oil lines improve appearance and reduce damage
Concealed oil lines through boom armConcealed oil lines through boom arm
#
Oil lines routed through the boom armOil lines routed through the boom arm
Oil lines routed through the torque tubeOil lines routed through the torque tube

Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage.

 

To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.

Specifications

Tractor
Model 7820/7830
Front tire 380/85R34
Rear tire 480/80R46
Front axle configuration
Wheelbase 2860 mm
112.6 in.
Pump capacity 96.1 L/min
25.4 gpm
Rated pressure 195 bar
2828 psi
Loader
Leveling configuration Mechanical Self Leveling (MSL)
Bucket used Materials 2450 mm
Materials - 85 in.
Bucket weight 352 kg
776 lb
Lift capacity at full height Measured at pivot (U)
2065 kg
4553 lbMeasured at 800 mm ahead of pivot (V)
2240 kg
4938 lb
Lift capacity at 59 in. (1500 mm) Measured at pivot (W)
3420 kg
7540 lbMeasured at 800 mm ahead of pivot (X)
3280 kg
7231 lb
Boom breakout force Measured at pivot (Y)
4793 kgf
10567 lbfMeasured at 800 mm ahead of pivot (Z)
4395 kgf
9689 lbf
Bucket rollback force capacity At maximum height (VV)
3641 kgf
8027 lbfAt 59-in. (1500-mm) lift height (XX)
4599 kgf
10139 lbfAt ground-level line (ZZ)
4640 kgf
10229 lbf
Dimensions Maximum lift height (A)
4650 mm
183.1 in.At full height - bucket level(B)
4465 mm
175.8 in.At full height - bucket dumped (C)
3820 mm
150.4 in.
Overall length (I+F), ft (m) 5.6 m
18.7 ft
Overall height in carry position (J) 2.4 m
7.8 ft
Digging depth (H) 150 mm
5.9 in.
Reach At maximum height (D)
820 mm
32.3 in.At ground level - bucket level (F)
2790 mm
109.8 in.
Bucket angle Dump angle, degrees (E)
-58.9 degree (angle)Rollback angle, degrees (G)
42 degree (angle)
Cycle times Loader raise, seconds
5 secondsLoader lower, seconds
5.5 secondsBucket dump, seconds
3.5 secondsBucket rollback, seconds
4 seconds
Additional information
Date collected

Accessories and Attachments

Ballast Box

Large Ballast Box - BW15852

Buckets

108 In. (2750 mm) Heavy Duty Global Bucket (Cat. 2) - BW15904
Heavy-duty bucket (shown with grapple)Heavy-duty bucket (shown with grapple)

The heavy-duty buckets for the H480 Loader have holes along the cutting edge where the replaceable and reversible cutting edge can be attached, providing more than twice the wear life for the cutting edge. They also include the brackets for attaching the grapple.

108 In. (2750 mm) High Volume Global Bucket (Cat. 2) - BW16004
High-volume bucket 2750 mm (108 in.)High-volume bucket 2750 mm (108 in.)
#

The high-volume bucket is intended for use with lighter-density high-volume materials. The bucket capacity makes this an effective tool for handling snow, wood shavings, and other loose materials. The high-volume bucket for the H480 Loader has holes along the cutting edge where the replaceable and reversible cutting edge can be attached, providing more than twice the wear life for the cutting edge.

96 In. (2450 mm) Heavy Duty Global Bucket (Cat. 2) - BW15903
Heavy-duty bucket (2450 mm shown with grapple)Heavy-duty bucket (2450 mm shown with grapple)
Heavy-duty bucket (2750 mm shown with grapple)Heavy-duty bucket (2750 mm shown with grapple)

The heavy-duty buckets for the H480 Loader have holes along the cutting edge where the replaceable and reversible cutting edge can be attached, providing more than twice the wear life for the cutting edge. They also include the brackets for attaching the grapple.

Cutting Edges

96 In. (2450 mm) Replaceable Bucket Cutting Edge with Hardware - BW14269
Replaceable wear edgeReplaceable wear edge
#

For those who frequently scrape on concrete, a replaceable cutting edge will greatly extend the life of the bucket:

  • 1850-mm (73-in.) width replaceable cutting edge
  • 2150-mm (85-in.) width replaceable cutting edge
  • 2450-mm (96-in.) width replaceable cutting edge
  • 2750-mm (108-in.) width replaceable cutting edge

GRAPPLES

Five-tine round bale and silage grapple with grille - BW16161
Five-tine round bale/silage grapple with grilleFive-tine round bale/silage grapple with grille
#

All of the H-Series Loaders use the same five-tine pin-on grapple. The advantages of this grapple are:

  • The pin-on method puts the least amount of stress possible on the bucket.
  • The grapple has a wide stance, making it more difficult to twist.

High-performance operators will choose the five-tine grapple for its increased durability and load-carrying capacity. Advantages include:

  • The ability to handle two large round bales instead of one (where loader capacity allows).
  • Strong grapple arms allow the bucket capacity to be increased by almost twice the amount of normal bucket capacity in materials such as silage.

The grapple is equipped with twin cylinders to provide excellent clamping force. 

NOTE: The center tine of the five-tine grapple is slightly off center to avoid contact with the placement of optional digging teeth.

NOTE: The grapple is not compatible with materials or high-volume buckets.

Guards

Hood Guard - BW15011
Hood guard for 8000 and 8010 TractorsHood guard for 8000 and 8010 Tractors

The hood guard can be mounted with or without a front weight bracket. When using the tractor without a loader, a maximum of 16 front weights can be used with the hood guard installed on 8000 and 8010 Series Tractors.

 

NOTE: BW15011 hood guard is compatible with 8020 Series Tractors without the front weight bracket. This is not recommended as the weight bracket does help prevent damage to the front of the tractor.

Hood Guard - BW15587

The tractor must be equipped with a front weight bracket in order to mount the hood guard.
When using the tractor without a loader, a maximum of 12 front weights can be used with the hood guard installed on 8020 Series Tractors.

Hood Guard - BW15629
Hood guard on 7730 MFWD TractorHood guard on 7730 MFWD Tractor
Hood guard for large-frame 7030 TractorsHood guard for large-frame 7030 Tractors

The hood guard's basic function is to:

  • Help protect the tractor grill and hood from falling debris or stationary objects such as a wagon or mixer
  • Allow for lighting at night 

 

Compatibility:

  • Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would over load the front axle)
  • Cannot be used with a front hitch

 

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so that the front weight bracket is the first point of contact against lower stationary objects.

The features of the hood guard include:

  • High height to better protect the top of the hood and to allow operators to see the top of the hood guard
  • Additional bolted-on front bar to protect the front grille against livestock damage
Hood Guard for 7R Series Tractors - BW15922
Hood guard on 7R TractorHood guard on 7R Tractor
Hood guard for 7R folded downHood guard for 7R folded down

The hood guard's basic function is to:

  • Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
  • Allow for lighting at night

Compatibility:

  • Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would overload the front axle)
  • Cannot be used with a front hitch

 

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so the front weight bracket is the first point of contact against lower stationary objects.

 

The features of the hood guard include:

  • High height to better protect the top of the hood and allow operators to see the top of the hood guard
  • Additional bolted-on front bar to protect the front grille against livestock damage
Hood Guard for 7R Series Tractors with Front Hitch - BW15959

The hood guard's basic function is to:

  • Help protect the tractor grill and hood from falling debris or stationary objects such as a wagon or mixer
  • Allow for lighting at night
Hood guard on 7R TractorHood guard on 7R Tractor
Hood guard for 7R folded downHood guard for 7R folded down

The hood guard's basic function is to:

  • Help protect the tractor grille and hood from falling debris or stationary objects such as a wagon or mixer
  • Allow for lighting at night

Compatibility:

  • Can be used with or without the tractor front weight bracket but not with the actual front weights while using the loader (this would over load the front axle)
  • Cannot be used with a front hitch

It is highly recommended to purchase a front weight bracket when using a loader. The hood guard is designed to be slightly rearward of the front weight bracket. This is so that the front weight bracket is the first point of contact against lower stationary objects.

 

The features of the hood guard include:

  • High height to better protect the top of the hood and to allow operators to see the top of the hood guard
  • Additional bolted-on front bar to protect the front grille against livestock damage
Hood Guard for 8R FT4 Tractors - BW16326
Hood guard for 8R and 8030 Series TractorsHood guard for 8R and 8030 Series Tractors
Hood guard shown on 8R Series TractorHood guard shown on 8R Series Tractor

The hood guard is designed to allow for the maximum amount of reach while protecting the hood and grille from falling objects. The hood guard also helps to protect the front of the tractor from impacts with wagons or feed mixers or whatever is being loaded.

The hood guard folds down to allow the hood to open, allowing access to service areas.

When using the tractor without a loader, a maximum of 12 front weights can be used with the hood guard installed on 8R and 8030 Series Tractors.

Hood Guard for 8R IT4, 8R Tier 3 and 8030 Series Tractor - BW15907
Hood guard for 8R and 8030 Series TractorsHood guard for 8R and 8030 Series Tractors
Hood guard shown on 8R Series TractorHood guard shown on 8R Series Tractor

The hood guard is designed to allow for the maximum amount of reach while protecting the hood and grille from falling objects. The hood guard also helps to protect the front of the tractor from impacts with wagons or feed mixers or whatever is being loaded.

The hood guard folds down to allow the hood to open, allowing access to service areas.

When using the tractor without a loader, a maximum of 12 front weights can be used with the hood guard installed on 8R and 8030 Series Tractors.

Hydraulic Connections

Grapple Single Point Coupler, Mobile Half - BW16011

This is the mobile half of the grapple single-point coupler required when ordering the loader for a tractor that has been ordered with a loader-ready package.

Hydraulic Fittings - BW16141
Single Point Hydraulic Connection Tractor Half and Grapple Mobile Half - BW15909

This is the mobile half of the grapple single-point coupler required when ordering the loader for a tractor that has been ordered with a loader-ready package.

Single Point Hydraulic Connection Tractor Half and Grapple Mobile Half - BWA1582
Single-point hydraulic connectionSingle-point hydraulic connection
Operating the hydraulic pressure relief knobOperating the hydraulic pressure relief knob

The H480 Loader features a single-point hydraulic connection that also incorporates the connection point for any electrical needs and the ability to relieve hydraulic pressure. In order to disconnect the hydraulic connection between the loader and the tractor, it has always been necessary to relieve the hydraulic system oil pressure. This has sometimes been difficult to accomplish and is also the reason why a coupling system was not offered on some tractors.

Now the ability to relieve the hydraulic oil system pressure is included with the single-point hydraulic connection, which allows for easily disconnecting both hydraulic and electrical lines to the loader from a convenient location with virtually no oil loss.

Single Point Hydraulic Connection Tractor Half and Grapple Mobile Half - BW16581
Single-point hydraulic connectionSingle-point hydraulic connection
Operating the hydraulic pressure relief knobOperating the hydraulic pressure relief knob

The H480 Loader features a single-point hydraulic connection that also incorporates the connection point for any electrical needs and the ability to relieve hydraulic pressure. In order to disconnect the hydraulic connection between the loader and the tractor, it has always been necessary to relieve the hydraulic system oil pressure. This has sometimes been difficult to accomplish and is also the reason why a coupling system was not offered on some tractors.

Now the ability to relieve the hydraulic oil system pressure is included with the single-point hydraulic connection, which allows for easily disconnecting both hydraulic and electrical lines to the loader from a convenient location with virtually no oil loss.

Single Point Hydraulic Connection Tractor Half and Grapple Mobile Half - BW16299

Hydraulic Controls

Electronic Single Lever Control - BW16065
Hoses and Parts (3 Function) - BW16272

On 8R, 8030, 8020, 8010, and 8000 Series Tractors, the H480 Loader uses rear tractor valves. There is no dedicated loader valve such as an independent control valve for the loader. The hydraulic hoses are routed from the connection point on the mounting frame to the rear tractor selective control valves (SCVs).

Hose connections to rear on 8R Series Tractors

The loader hydraulic hoses can be connected to three rear SCVs. It is recommended that tractors be ordered with five rear SCVs when utilizing an H480 loader.

Hose connections to rear on 8030 Series Tractors
Rear hydraulic setup with third-function valveRear hydraulic setup with third-function valve
Rear auxiliary valve kit (close-up)Rear auxiliary valve kit (close-up)

The loader hydraulic hoses can be connected to three rear SCVs or two rear SCVs and a rear auxiliary valve kit to provide the third-function service.

Loader hoses hook into SCVs number 3 and 4. The auxiliary valve kit for third function is shown in the following pictures with couplers attached to the valve. The couplers are not included in the bundle and must be ordered from service parts if desired.

For 8030 Series Tractors (s/n 039999 and below) without 5th SCV, order 1-RE241359 Grapple Valve Kit (grapple valve requires four rear SCVs; if not equipped with four rear SCVs, order 1-RE238579), 1-AR243091 Single Lever Control Kit, 1-RE219046 SCO Control Unit, 1-RE250961 Wiring Harness, and 1-R247855 Software Download (software download available from PDC).

For 8030 Series Tractors (s/n 039999 and below) with 5th SCV, order 1-RE241359 Grapple Valve Kit and 1-AR243091 Single Lever Control Kit.

For 8030 Series Tractors (s/n 040000 and above) without 5th SCV, order 1-RE283389 Grapple Valve Kit and 1-AR243091 Single Lever Control Kit.

For 8030 Series Tractors (s/n 040000 and above) with 5th SCV, order 1-AR243091 Single Lever Control Kit.

Hose connections to rear on 8000, 8010, and 8020 Series Tractors
Third-function utilizing electrohydraulic valveThird-function utilizing electrohydraulic valve
Third-function hydraulic hosesThird-function hydraulic hoses

The loader hydraulic hoses can be connected to three rear SCVs or two rear SCVs and a rear auxiliary electrohydraulic valve kit to provide the third-function service.

Hydraulic Hoses and Mid-Mount Adapter - BW16162

The loader hoses are connected to the mid tractor selective control valves (SCVs).

Hydraulic Hoses and Parts (3 Function) - BW15910

On 8R, 8030, 8020, 8010, and 8000 Series Tractors, the H480 Loader uses rear tractor valves. There is no dedicated loader valve such as an independent control valve for the loader. The hydraulic hoses are routed from the connection point on the mounting frame to the rear tractor selective control valves (SCVs).

Hose connections to rear on 8R Series Tractors

The loader hydraulic hoses can be connected to three rear SCVs. It is recommended that tractors be ordered with five rear SCVs when utilizing an H480 loader.

Hose connections to rear on 8030 Series Tractors
Rear hydraulic setup with third-function valveRear hydraulic setup with third-function valve
Rear auxiliary valve kit (close-up)Rear auxiliary valve kit (close-up)

The loader hydraulic hoses can be connected to three rear SCVs or two rear SCVs and a rear auxiliary valve kit to provide the third-function service.

Loader hoses hook into SCVs number 3 and 4. The auxiliary valve kit for third function is shown in the following pictures with couplers attached to the valve. The couplers are not included in the bundle and must be ordered from service parts if desired.

For 8030 Series Tractors (s/n 039999 and below) without 5th SCV, order 1-RE241359 Grapple Valve Kit (grapple valve requires four rear SCVs; if not equipped with four rear SCVs, order 1-RE238579), 1-AR243091 Single Lever Control Kit, 1-RE219046 SCO Control Unit, 1-RE250961 Wiring Harness, and 1-R247855 Software Download (software download available from PDC).

For 8030 Series Tractors (s/n 039999 and below) with 5th SCV, order 1-RE241359 Grapple Valve Kit and 1-AR243091 Single Lever Control Kit.

For 8030 Series Tractors (s/n 040000 and above) without 5th SCV, order 1-RE283389 Grapple Valve Kit and 1-AR243091 Single Lever Control Kit.

For 8030 Series Tractors (s/n 040000 and above) with 5th SCV, order 1-AR243091 Single Lever Control Kit.

Hose connections to rear on 8000, 8010, and 8020 Series Tractors
Third-function utilizing electrohydraulic valveThird-function utilizing electrohydraulic valve
Third-function hydraulic hosesThird-function hydraulic hoses

The loader hydraulic hoses can be connected to three rear SCVs or two rear SCVs and a rear auxiliary electrohydraulic valve kit to provide the third-function service.

Hydraulic Hoses and Parts (3 Function) - BWA1521
Hydraulic Hoses and Parts (3 Function) - BW16269

The loader hoses are connected to the mid tractor selective control valves (SCVs).

Hydraulic Hoses and Parts (3 Function) - BW16298

The loader hoses are connected to the mid tractor selective control valves (SCVs).

Hydraulic Hoses and Parts (3 Function) for 7R IT4 - BW16147

The loader hoses are connected to the mid tractor selective control valves (SCVs).

Single Lever Control, Hoses & Parts (3 Function) - BWA1520

LOADER MOUNTED FENDERS

Stationary fenders - BW15928
Stationary fender (H480 shown)Stationary fender (H480 shown)
#

Loader stationary fenders are highly recommended for those operating in conditions where the front axle will be in full oscillation and turn frequently or where tight turns are made while maneuvering through gates or obstacles that will catch tractor axle-mounted fenders.

 

The loader stationary fenders still provide coverage for debris from the tire, but they do not protrude to become damaged in operation. The fenders can be removed to enable better access for servicing as well.

LOADER SUSPENSION SYSTEM

Loader suspension system with operator station on and off switch - BW15974
Nitrogen-charged accumulator and electric valveNitrogen-charged accumulator and electric valve
Loader suspension and electric remote carrier latch rocker switch panelLoader suspension and electric remote carrier latch rocker switch panel

A feature intended to improve loader productivity, the LSS allows the boom cylinders to float,
reducing the jarring effects loads are prone to over rough terrain.

  • An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
  • The cylinders move in and out to allow the boom to float
  • Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain
  • Pallets can be moved easily without sustaining cargo damage
  • Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
  • Extended life of loader pins and bushings
  • Less stress on the tractor axle
  • Properly ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Reasons for turning LSS off include:

  • Digging applications- with LSS on, the cylinders retract slightly, losing lifting power
  • Holding a grade when blading – with LSS on, it is difficult to hold a constant grade
  • Precise pallet and bale handling – with LSS on, the load moves up and down slightly while being positioned
  • Parking a loader – with LSS on, when down-pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The loader suspension system is controlled by a switch conveniently located in the operator station so it can be easily reached for activation or deactivation as needed. 

Loader suspension system with operator station on and off switch for 7R Final Tier 4 (FT4) Model Year 2014 (MY 2014) - BW16305
Nitrogen-charged accumulator and electric valveNitrogen-charged accumulator and electric valve
Loader suspension and electric remote carrier latch rocker switch panelLoader suspension and electric remote carrier latch rocker switch panel

A feature intended to improve loader productivity, the LSS allows the boom cylinders to float,
reducing the jarring effects loads are prone to over rough terrain.

  • An accumulator charged with nitrogen and connected to the head-end lift cylinder hose through a T-fitting provides shock absorption
  • The cylinders move in and out to allow the boom to float
  • Bales can be transported more efficiently from one end of the field to the other over frozen, hard-packed, or rutted terrain
  • Pallets can be moved easily without sustaining cargo damage
  • Pallets of seed or fertilizer can be carried across a yard without a bag spilling and creating a costly mess
  • Extended life of loader pins and bushings
  • Less stress on the tractor axle
  • Properly ballasted tractor with LSS has increased stability, creating a smoother ride for the operator

Reasons for turning LSS off include:

  • Digging applications- with LSS on, the cylinders retract slightly, losing lifting power
  • Holding a grade when blading – with LSS on, it is difficult to hold a constant grade
  • Precise pallet and bale handling – with LSS on, the load moves up and down slightly while being positioned
  • Parking a loader – with LSS on, when down-pressure is applied, the lift cylinders retract slightly, making it more difficult to park

The loader suspension system is controlled by a switch conveniently located in the operator station so it can be easily reached for activation or deactivation as needed. 

Miscellaneous

108 In. (2750 mm) Replaceable Bolt-On Wear Edge - W44540
Digging Teeth - BW15763

Digging teeth can be added to the heavy-duty bucket for easier digging in hard ground or for breaking loose hard-packed materials such as manure or silage. Digging teeth are not compatible with replaceable cutting edges.

Mounting Frame Components

Tool Box Bracket - BW15929
Tool Box Bracket - BW16306

OPERATOR'S MANUAL AND DECAL KIT

French North American operator's manual and decal kit - BW16001
Spanish North American operator's manual and decal kit - BW16002

QUICK UNLATCH

Electric remote carrier latching system - BW16991

The electric remote carrier latching system provides enhanced productivity and improved operator comfort when changing loader attachments. This time-saving feature allows an operator to unlatch and latch attachments for Global or Global Category 2 Carriers without leaving the operator's station.

Electric remote carrier latching system on H340 LoaderElectric remote carrier latching system on H340 Loader
#

To watch a video of the remote carrier latching system, click here.

Unlike competitive remote latching systems, the John Deere electric remote carrier latching system utilizes a simple electric actuator instead of third function hydraulics and/or diverter valves for the loader.

REGIONAL REQUIREMENT KITS

Australia service lock bundle - BW16192

Tractor Mounting Frames

Mounting Frame - BW15933
Mounting Frame - BW15947
Mounting Frame - BW15888
Mounting Frame - BW16270
Mounting Frame - BW16271
Mounting Frame and Tool Box - BWA1526
Right-hand mounting frameRight-hand mounting frame
Left-hand mounting frameLeft-hand mounting frame
Mounting frames - Large-frame 7030/7020 TractorsMounting frames - Large-frame 7030/7020 Tractors

Frames are designed to evenly distribute forces during loader operation. Hardware is easily accessible to torque to the correct specification.

For the large-frame 7030 and 7020 Series Tractors, a cast design is utilized to provide better visibility, as a casting allows for sculpting the shape to improve sight lines.

Mounting Frame for 7R FT4 and 7R IT4 Series Tractors - BW16467
Mounting Frame with Tool Box Kit - BWA1523
Mounting frame for 8R and 8030 Series TractorsMounting frame for 8R and 8030 Series Tractors

Frames are designed to evenly distribute forces during loader operation. Hardware is easily accessible to torque to the correct specification level.

 

The hardware for the 8 Series Tractors consists of a combination of studs and cones for additional torque capability, ensuring proper engagement to the tractor frame.

Mounting Frame with Tool Box Kit - BWA1524
Mounting frame - 8030/8R Series Tractors with IVTMounting frame - 8030/8R Series Tractors with IVT

For 8030 and 8R Series Tractors with IVT transmissions, a unique mounting frame is required in order to properly interface with the tractor frame.

Hardware is easily accessible to torque to the correct specification level. The hardware for the 8000 Series Tractors consists of a combination of studs and cones for a secure, tight fit.